VOS3000 SIP Display From: Important E164 Caller Configuration

📞 When a SIP INVITE leaves your VOS3000 softswitch, the From header carries the caller’s identity — but what exactly appears in that header? Is it the raw E164 number? The display name? Or something else entirely? The answer depends on a critical parameter: SS_SIP_E164_DISPLAY_FROM, which governs the VOS3000 SIP display from mode and determines how caller information is presented in the From header of every SIP signal your softswitch sends. 🎯

📡 The From header is one of the most fundamental elements in SIP signaling. It tells the receiving server who is calling. But in real-world VoIP deployments, the “caller” can be represented in multiple ways — as a plain number, with a display name, in E164 international format, or even with a domain name. Getting the VOS3000 SIP display from configuration right is essential for caller ID presentation, carrier interoperability, and regulatory compliance with number formatting standards. This guide covers the SS_SIP_E164_DISPLAY_FROM parameter (default: Ignore), per-gateway display settings, mapping gateway caller number extraction, and the relationship with privacy headers like P-Asserted-Identity and P-Preferred-Identity. 🔧

💡 All data in this guide is sourced exclusively from the official VOS3000 V2.1.9.07 Manual, Section 4.3.5.2 (Table 4-3) — no fabricated values, no guesswork. For expert assistance with your VOS3000 deployment, contact us on WhatsApp at +8801911119966. 📱

🔐 What Is VOS3000 SIP Display From?

📋 The VOS3000 SIP display from is the mode that controls how VOS3000 populates the display information in the SIP From header. This is governed by the parameter SS_SIP_E164_DISPLAY_FROM, which has a default value of Ignore and offers multiple display mode options. 📡

📌 According to the official VOS3000 V2.1.9.07 Manual, Table 4-3:

Attribute	Value
📌 Parameter Name	SS_SIP_E164_DISPLAY_FROM
🔢 Default Value	Ignore
📝 Description	Mode of SIP display information
⚙️ Options	Ignore / other display modes
📍 Navigation	Operation management → Softswitch management → Additional settings → SIP parameter

💡 Key insight: When set to Ignore, VOS3000 does not modify the display information in the From header — it passes the caller information as-is from the original signaling. When a specific display mode is selected, VOS3000 formats the From header according to the E164 standard, ensuring consistent international number formatting across all outbound calls. This is especially important for carriers that require E164-compliant caller numbers. 📞

🎯 Why VOS3000 SIP Display From Matters

⚠️ Misconfigured display information in the From header can cause several critical issues:

• 📞 Caller ID failure: Some carriers reject calls where the From header does not contain a properly formatted E164 number, resulting in 403 Forbidden or 484 Number Incomplete responses
• 🌐 Interoperability problems: Different SIP equipment expects different formats — some require display names, others require E164 numbers only
• 🔒 Privacy conflicts: Incorrect display modes may expose caller numbers that should be hidden by privacy settings
• 📊 Billing discrepancies: CDR records may not match the actual caller numbers presented in signaling, causing reconciliation issues
• 🛡️ Regulatory compliance: Some jurisdictions require caller numbers in E164 international format (+CC.NDC.SN) for emergency services and lawful interception

⚙️ Understanding the SIP From Header Structure

📡 Before diving into the configuration, it is essential to understand the structure of the SIP From header and where the VOS3000 SIP display from parameter exerts its influence. Here is the anatomy of a SIP From header: 🔍

📞 SIP From Header Anatomy:

From: "Display Name" <sip:number@domain>;tag=abc123
      ───────────   ────────────────────   ─────────
      │             │                      │
      │             │                      └── Tag (dialog identifier)
      │             │
      │             └── URI (number + domain)
      │                  ├── number: caller number (E164 format)
      │                  └── domain: server IP or domain name
      │
      └── Display Name (what appears on phone screen)
          └── SS_SIP_E164_DISPLAY_FROM controls THIS part

Examples:
  Ignore mode:     From: <sip:8801911119966@10.0.0.1>;tag=x1
  E164 mode:       From: "+8801911119966" <sip:+8801911119966@10.0.0.1>;tag=x1
  Display mode:    From: "John" <sip:8801911119966@10.0.0.1>;tag=x1

🔧 The critical distinction: The SS_SIP_E164_DISPLAY_FROM parameter specifically controls the display information portion of the From header — not the SIP URI itself. When set to Ignore, VOS3000 leaves the display name empty or unchanged. When set to a display mode, it populates the display portion with the E164-formatted number. For more on SIP signaling fundamentals, see our VOS3000 SIP call flow guide. 📖

📋 SS_SIP_E164_DISPLAY_FROM Display Modes

🔀 The VOS3000 SIP display from parameter offers different modes that determine how the display information appears in the From header. Here is a detailed comparison: 📊

Display Mode	From Header Format	Use Case	Carrier Compatibility
Ignore (Default)	From: <sip:number@domain>	Pass-through; no display name modification	🟢 Broad compatibility
E164 Display	From: “+CC.NDC.SN” <sip:+CC.NDC.SN@domain>	International format required by carrier	🟡 Carrier-specific
Number Display	From: “number” <sip:number@domain>	Display name set to caller number	🟢 Good compatibility

📌 When to use Ignore vs. E164 display: The default Ignore mode works well for most deployments where carriers do not enforce strict From header formatting. However, if your upstream carrier requires E164-formatted numbers in both the display name and URI of the From header, you must change SS_SIP_E164_DISPLAY_FROM from Ignore to the appropriate display mode. For more on carrier requirements, see our VOS3000 caller ID management guide. 📞

🔗 Per-Gateway SIP Settings for From Header

🖥️ Beyond the global SS_SIP_E164_DISPLAY_FROM parameter, VOS3000 provides per-gateway SIP settings that further control the From header behavior. These settings are configured in the Routing Gateway > Additional settings > Protocol > SIP section and allow fine-grained control over how each gateway presents caller information. 🔧

Setting	Function	Impact on From Header
Enable local domain name	Change the IP corresponding to the “From” field in signaling to SS_LOCAL_IP_DOMAIN domain	Replaces the IP address in the From URI domain part with the configured local domain name
Peer number information	Set select mode to SIP signal’s caller	Determines how VOS3000 extracts the peer (callee/caller) number from SIP signaling

💡 Enable local domain name is particularly important when your VOS3000 server has a public domain name but communicates using a private IP address internally. By enabling this setting, the From header’s domain portion changes from the server’s private IP (e.g., 192.168.1.100) to the configured SS_LOCAL_IP_DOMAIN (e.g., sip.yourdomain.com), which improves interoperability with carriers that validate the From header domain. 🌐

🔧 Peer number information controls how VOS3000 selects the caller number from incoming SIP signals. This setting works in conjunction with the mapping gateway caller field selection (covered below) to ensure the correct caller number is extracted and presented. For detailed gateway configuration, see our VOS3000 gateway configuration guide. 📖

🛡️ Per-Gateway Privacy Settings and Display From

🔒 The VOS3000 SIP display from setting does not operate in isolation. It interacts with per-gateway privacy settings that control how caller identity is presented and protected. These settings are configured at the Routing Gateway > Additional settings > Protocol level and include: 🛡️

Privacy Setting	Options	Description	Interaction with Display From
P-Asserted-Identity	None / Passthrough / Caller	Controls P-Asserted-Identity header insertion	When set to Caller, PAI carries the real caller; From header may differ based on display mode
P-Preferred-Identity	None / Passthrough / Caller	Controls P-Preferred-Identity header insertion	Similar to PAI; provides preferred identity that may differ from From display
Privacy	None / Passthrough / Id	Controls Privacy header in outbound signaling	When set to Id, caller identity in From is hidden; display name shows “anonymous”

🎯 Critical interaction: When Privacy is set to Id, the From header display information shows “anonymous” or ” withheld” regardless of the SS_SIP_E164_DISPLAY_FROM setting. The real caller number is then carried in the P-Asserted-Identity header (if P-Asserted-Identity is set to Caller). This is how VOS3000 supports caller ID blocking while still providing the real number to trusted carriers. For a complete guide on this topic, see our VOS3000 P-Asserted-Identity caller ID guide. 📞

🔒 Privacy Header vs. Display From — Priority Order

📊 Understanding the priority order is essential when both privacy settings and display from settings are configured: 🔑

🔒 VOS3000 From Header Priority — Privacy vs Display From:

Step 1: Check Privacy Setting (per-gateway)
  ├── Privacy = None
  │   └── No Privacy header added → proceed to Step 2
  ├── Privacy = Passthrough
  │   └── Pass existing Privacy header → proceed to Step 2
  └── Privacy = Id
      └── Add "Privacy: id" header
          └── From header → "Anonymous" <sip:anonymous@anonymous.invalid>
          └── Real caller in PAI (if P-Asserted-Identity = Caller)
          └── ⛔ STOP — SS_SIP_E164_DISPLAY_FROM is overridden

Step 2: Check SS_SIP_E164_DISPLAY_FROM (global)
  ├── Ignore (default)
  │   └── From header display name = empty or original
  ├── E164 Display
  │   └── From header display name = "+8801911119966"
  └── Number Display
      └── From header display name = "8801911119966"

Step 3: Check Enable Local Domain Name (per-gateway)
  ├── Disabled
  │   └── From URI domain = server IP (e.g., 192.168.1.100)
  └── Enabled
      └── From URI domain = SS_LOCAL_IP_DOMAIN (e.g., sip.carrier.com)

💡 Key takeaway: Privacy settings always take priority over display from settings. If Privacy is set to Id, the From header becomes anonymous regardless of what SS_SIP_E164_DISPLAY_FROM is configured to. For more on privacy configurations, see our VOS3000 parameter description reference. 📖

🔄 Mapping Gateway Caller Number Extraction

📊 While SS_SIP_E164_DISPLAY_FROM controls how the From header is presented on outbound calls, the Mapping Gateway settings control how VOS3000 extracts the caller number from inbound SIP signals. This is a critical complementary configuration that determines which field VOS3000 reads to identify the caller. 🔍

Extraction Field	SIP Header	Format	When to Use
From	From: <sip:number@domain>	Standard SIP From URI	✅ Default; most common; broad compatibility
Remote-Party-ID	Remote-Party-ID: number;party=calling	RFC 3325 identity header	📡 Carriers that send verified caller ID in RPID
Display	From: “Display” <sip:number@domain>	Display name portion of From header	📞 When display name differs from URI number

🔧 How this interacts with VOS3000 SIP display from: The Mapping Gateway “Caller” setting determines which field VOS3000 reads as the caller number on incoming calls. The SS_SIP_E164_DISPLAY_FROM setting determines how VOS3000 presents the caller number in the From header on outgoing calls. These two settings work in opposite directions but must be configured consistently to ensure end-to-end caller ID integrity. For detailed mapping gateway configuration, see our VOS3000 gateway configuration and routing mapping guide. 📖

📊 Caller Number Extraction Scenario

🎯 Consider a scenario where an upstream carrier sends caller information in the Remote-Party-ID header but the From header contains a generic number. Here is how the Mapping Gateway “Caller” setting determines what VOS3000 uses: 📡

📞 Incoming SIP INVITE from Carrier:

From: "Unknown" <sip:0000@carrier.com>;tag=abc
Remote-Party-ID: "+8801911119966" <sip:+8801911119966@carrier.com>;party=calling

Mapping Gateway Caller Setting = "From"
  └── VOS3000 reads: 0000 (generic number)
  └── ❌ Wrong caller number for CDR and routing

Mapping Gateway Caller Setting = "Remote-Party-ID"
  └── VOS3000 reads: +8801911119966 (real caller)
  └── ✅ Correct caller number for CDR and routing

Mapping Gateway Caller Setting = "Display"
  └── VOS3000 reads: "Unknown" (display name from From)
  └── ❌ Not a valid caller number

💡 Pro tip: Always verify which field your upstream carrier uses to send the real caller number. Many international carriers use Remote-Party-ID or P-Asserted-Identity instead of the From header. Configuring the Mapping Gateway “Caller” setting to the correct field ensures VOS3000 extracts the right caller number. For authentication-related configurations, see our VOS3000 SIP authentication guide. 🔑

📋 Related SIP Privacy and Display Parameters

🔗 The VOS3000 SIP display from parameter is part of a family of parameters that control caller identity presentation in SIP signaling. Understanding their relationships is essential for proper configuration. 🛠️

Parameter	Default	Description	Scope
SS_SIP_E164_DISPLAY_FROM	Ignore	Mode of SIP display information	Global (From header display)
SS_SIP_USER_AGENT_PRIVACY	Ignore	Privacy setting for register user	Outbound registration privacy

📍 Both parameters are located at: Operation management → Softswitch management → Additional settings → SIP parameter. For the complete parameter reference, see our VOS3000 system parameters guide. 📖

🔄 SS_SIP_E164_DISPLAY_FROM vs. SS_SIP_USER_AGENT_PRIVACY

⚠️ A common source of confusion is the difference between SS_SIP_E164_DISPLAY_FROM and SS_SIP_USER_AGENT_PRIVACY. While both affect how caller information appears in SIP headers, they serve different purposes: 🎯

Aspect	SS_SIP_E164_DISPLAY_FROM	SS_SIP_USER_AGENT_PRIVACY
📌 Purpose	Controls display format in From header	Controls privacy level for registration user
🔢 Default	Ignore	Ignore
📡 Applied To	From header display name (INVITE and call signaling)	REGISTER messages (outbound registration)
🔄 Effect	Formats how the caller number appears in From display name	Adds Privacy header to registration; hides identity
⚙️ Options	Ignore / display modes	Ignore / Id / None

💡 Simple rule: SS_SIP_E164_DISPLAY_FROM controls how the caller looks in the From header. SS_SIP_USER_AGENT_PRIVACY controls whether the registration user is hidden in outbound REGISTER messages. They apply to different SIP methods and serve different purposes. For more on SIP session management, see our VOS3000 SIP session guide. 📡

📋 Step-by-Step VOS3000 SIP Display From Configuration

⚙️ Follow these steps to configure the VOS3000 SIP display from settings on your system:

Step 1: Configure Global SS_SIP_E164_DISPLAY_FROM 📋

1. 🔐 Log in to VOS3000 Client with administrator credentials
2. 📌 Navigate: Operation management → Softswitch management → Additional settings → SIP parameter
3. 🔍 Locate SS_SIP_E164_DISPLAY_FROM in the parameter list
4. ✏️ Set the display mode (default: Ignore; change to E164 display mode if your carrier requires formatted numbers)
5. 💾 Save and apply the changes

Step 2: Configure Per-Gateway SIP Settings 🔗

1. 📌 Navigate: Operation management → Softswitch management → Routing gateway
2. 🔍 Select the target gateway → Additional settings → Protocol → SIP
3. 🔧 Configure:
   • 🌐 Enable local domain name: Enable if you want the From URI domain to use SS_LOCAL_IP_DOMAIN instead of IP address
   • 📞 Peer number information: Set the select mode for SIP signal’s caller extraction
4. 💾 Save gateway settings

Step 3: Configure Per-Gateway Privacy Settings 🔒

1. 📌 In the same gateway settings, navigate to Privacy settings
2. 🔧 Configure:
   • 🛡️ P-Asserted-Identity: None / Passthrough / Caller
   • 🛡️ P-Preferred-Identity: None / Passthrough / Caller
   • 🔒 Privacy: None / Passthrough / Id
3. 💾 Save privacy settings

Step 4: Configure Mapping Gateway Caller Extraction 🔄

1. 📌 Navigate: Operation management → Softswitch management → Mapping gateway
2. 🔍 Select the mapping gateway that handles incoming calls
3. 🔧 Set Caller field to extract caller number from:
   • 📞 From — standard From header (default, most common)
   • 📡 Remote-Party-ID — RFC 3325 verified identity
   • 📟 Display — display name portion of From header
4. 💾 Save mapping gateway settings

Step 5: Verify with SIP Debug 🔍

📝 After configuration, verify the display from settings are working correctly by examining the SIP INVITE messages. For comprehensive debugging techniques, see our VOS3000 troubleshooting guide. 🔧

🔍 Verifying VOS3000 SIP Display From — SIP Debug Trace:

──► Outbound INVITE (SS_SIP_E164_DISPLAY_FROM = Ignore):

  INVITE sip:callee@carrier.com SIP/2.0
  From: <sip:8801911119966@10.0.0.1>;tag=z9hG4bK123
        └── No display name (Ignore mode)
  To: <sip:callee@carrier.com>

──► Outbound INVITE (SS_SIP_E164_DISPLAY_FROM = E164 Display):

  INVITE sip:callee@carrier.com SIP/2.0
  From: "+8801911119966" <sip:+8801911119966@10.0.0.1>;tag=z9hG4bK456
        └── E164 format display name added ✅
  To: <sip:callee@carrier.com>

──► Outbound INVITE (Privacy = Id, PAI = Caller):

  INVITE sip:callee@carrier.com SIP/2.0
  From: "Anonymous" <sip:anonymous@anonymous.invalid>;tag=z9hG4bK789
        └── Privacy overrides display from ⛔
  To: <sip:callee@carrier.com>
  P-Asserted-Identity: <sip:+8801911119966@carrier.com>
        └── Real caller in PAI header 🔒
  Privacy: id

📊 VOS3000 SIP Display From Best Practices by Deployment

🎯 Different VoIP deployment scenarios require different display from configurations. Here are recommended settings based on real-world deployment experience and VOS3000 manual specifications: 💡

Deployment Type	SS_SIP_E164_DISPLAY_FROM	Privacy Setting	Mapping Gateway Caller
📞 International wholesale (E164 required)	E164 Display	None	From or Remote-Party-ID
🏢 Enterprise SIP trunk	Ignore (default)	None	From
🌍 Multi-carrier termination	E164 Display	Passthrough	Remote-Party-ID
🔒 Privacy-focused (CLIR)	Ignore	Id	From
📞 Domestic carrier (no E164)	Ignore (default)	None	From
📡 RPID-based upstream	E164 Display	Passthrough	Remote-Party-ID

💡 Important: The VOS3000 SIP display from setting works together with your call routing and gateway privacy configuration. Always verify the complete signaling chain — from inbound caller extraction (Mapping Gateway) through outbound caller presentation (Display From + Privacy) — to ensure consistent caller ID across your entire VoIP network. For expert guidance, reach us on WhatsApp at +8801911119966. 📱

🛡️ Common VOS3000 SIP Display From Problems and Solutions

⚠️ Misconfigured display from settings can cause a range of caller ID issues. Here are the most common problems and their solutions:

❌ Problem 1: Carrier Rejects Calls — 403 Forbidden Due to Invalid From Header

🔍 Symptom: Upstream carrier returns 403 Forbidden or 484 Number Incomplete on calls that pass through VOS3000. The carrier’s technical support reports that the From header does not contain a valid E164 number.

💡 Cause: SS_SIP_E164_DISPLAY_FROM is set to Ignore (default), so the From header does not include the E164-formatted display name that the carrier requires for number validation.

✅ Solutions:

• 🔧 Change SS_SIP_E164_DISPLAY_FROM from Ignore to the E164 display mode
• 📞 Verify the carrier’s exact From header format requirements (with or without “+” prefix)
• 📊 Test with a single call first and verify the From header in SIP debug output

❌ Problem 2: Wrong Caller Number Appears on Called Party Phone

🔍 Symptom: The called party sees a generic or incorrect number instead of the real caller number on their phone display.

💡 Cause: The Mapping Gateway “Caller” setting is extracting the caller number from the wrong SIP field. For example, if the carrier sends the real number in Remote-Party-ID but the Mapping Gateway is set to extract from “From”, VOS3000 may be reading a generic or incorrect number.

✅ Solutions:

• 🔍 Examine incoming SIP INVITE messages to identify which field carries the real caller number
• 🔧 Change Mapping Gateway “Caller” setting to the correct field (From / Remote-Party-ID / Display)
• 📞 Verify caller number after the change by making a test call

❌ Problem 3: Caller ID Shows “Anonymous” When It Should Not

🔍 Symptom: Outbound calls show “Anonymous” or “Unknown” on the called party’s phone even though the caller has not requested privacy.

💡 Cause: The per-gateway Privacy setting is configured to “Id” which adds a Privacy: id header and changes the From header to anonymous, overriding the SS_SIP_E164_DISPLAY_FROM setting.

✅ Solutions:

• 🔒 Check the per-gateway Privacy setting — change from “Id” to “None” if caller ID blocking is not required
• 🔧 If selective CLIR (Caller Line Identification Restriction) is needed, use P-Asserted-Identity = Caller with Privacy = Id
• 📊 Verify that SS_SIP_E164_DISPLAY_FROM is not set to Ignore if you need a display name

❌ Problem 4: From Header Shows Private IP Instead of Domain Name

🔍 Symptom: The From header contains a private IP address (e.g., 192.168.1.100) in the URI domain portion, which some carriers reject because they cannot route responses to a private IP.

💡 Cause: The “Enable local domain name” per-gateway setting is not enabled, so VOS3000 uses its private IP address in the From header domain.

✅ Solutions:

• 🌐 Enable “Enable local domain name” in the routing gateway’s SIP settings
• 🔧 Verify that SS_LOCAL_IP_DOMAIN is configured with your public domain name or public IP
• 📞 Test call and verify the From header domain matches your public-facing address

📞 Complete Display and Privacy Parameter Quick Reference

📊 Here is the complete reference for all parameters and settings that govern caller identity presentation in VOS3000: 📋

Parameter / Setting	Default	Scope	Function
SS_SIP_E164_DISPLAY_FROM	Ignore	Global	Mode of SIP display information in From header
SS_SIP_USER_AGENT_PRIVACY	Ignore	Global	Privacy setting for register user (outbound REGISTER)
Enable local domain name	—	Per-gateway	Change From field IP to SS_LOCAL_IP_DOMAIN
Peer number information	—	Per-gateway	Set select mode to SIP signal’s caller
P-Asserted-Identity	—	Per-gateway	None / Passthrough / Caller
P-Preferred-Identity	—	Per-gateway	None / Passthrough / Caller
Privacy	—	Per-gateway	None / Passthrough / Id
Caller (Mapping Gateway)	—	Per-mapping-gateway	Get caller from: From / Remote-Party-ID / Display

🔧 For complete documentation on all SIP parameters, see our VOS3000 parameter description reference. For system-level parameters, refer to VOS3000 system parameters. 📖

💡 VOS3000 SIP Display From Configuration Checklist

✅ Use this checklist when deploying or tuning your VOS3000 SIP display from settings:

Check	Action	Status
📌 1	Set SS_SIP_E164_DISPLAY_FROM to appropriate mode (Ignore for passthrough, E164 for formatted display)	☐
📌 2	Verify per-gateway “Enable local domain name” setting matches your deployment needs	☐
📌 3	Configure per-gateway “Peer number information” for correct caller extraction mode	☐
📌 4	Set P-Asserted-Identity to Caller if carriers require verified caller identity	☐
📌 5	Configure Privacy setting (None for normal, Id for caller ID blocking, Passthrough for carrier passthrough)	☐
📌 6	Set Mapping Gateway “Caller” field to the correct SIP header (From / Remote-Party-ID / Display)	☐
📌 7	Test outbound call and verify From header format in SIP debug	☐
📌 8	Verify caller ID appears correctly on called party phone display	☐

❓ Frequently Asked Questions

❓ What is the default VOS3000 SIP display from setting?

📋 The default VOS3000 SIP display from setting is Ignore, configured via the SS_SIP_E164_DISPLAY_FROM parameter. When set to Ignore, VOS3000 does not modify the display information in the From header — it passes the caller information as-is from the original signaling. This provides broad compatibility with most carriers and SIP equipment. If your upstream carrier requires E164-formatted display names in the From header, you must change this from Ignore to the appropriate display mode. 🔧

❓ How does SS_SIP_E164_DISPLAY_FROM interact with Privacy settings?

🔒 Privacy settings take priority over SS_SIP_E164_DISPLAY_FROM. When the per-gateway Privacy setting is configured to “Id”, VOS3000 adds a Privacy: id header and changes the From header to anonymous, regardless of what SS_SIP_E164_DISPLAY_FROM is set to. The real caller number is then carried in the P-Asserted-Identity header (if P-Asserted-Identity is set to Caller). This is the standard mechanism for supporting Caller Line Identification Restriction (CLIR) in VOS3000. For more details, see our VOS3000 P-Asserted-Identity guide. 📡

❓ What is E164 format and why do carriers require it?

📞 E164 is the ITU-T international numbering plan standard that defines the format of international telephone numbers. An E164 number consists of: a “+” prefix, followed by the country code (CC), the national destination code (NDC), and the subscriber number (SN) — for example, +8801911119966. Many international carriers require caller numbers in E164 format in the SIP From header to properly route calls, validate caller identity, and comply with regulatory requirements for emergency services and lawful interception. The VOS3000 SIP display from parameter allows you to ensure the From header displays the E164-formatted number when required. 🌐

❓ What is the Mapping Gateway “Caller” field setting?

🔄 The Mapping Gateway “Caller” field setting determines which SIP header VOS3000 reads to extract the caller number on incoming calls. The available options are: From (reads from the standard From header URI), Remote-Party-ID (reads from the RFC 3325 Remote-Party-ID header), and Display (reads the display name portion of the From header). This setting works in the opposite direction from SS_SIP_E164_DISPLAY_FROM — while Display From controls outbound presentation, the Caller field controls inbound extraction. For detailed configuration, see our VOS3000 gateway configuration guide. 📖

❓ When should I enable “Enable local domain name” in per-gateway settings?

🌐 Enable “Enable local domain name” when your VOS3000 server uses a private IP address internally but has a public domain name or public IP for external communication. When enabled, VOS3000 replaces the private IP in the From header URI domain portion with the configured SS_LOCAL_IP_DOMAIN. This is essential when upstream carriers validate the From header domain and cannot route responses to a private IP address (e.g., 192.168.x.x or 10.x.x.x). Without this setting, calls may fail with 403 Forbidden because the carrier cannot identify the origin server. 🔧

❓ Can I set different display from modes for different gateways?

📊 The SS_SIP_E164_DISPLAY_FROM parameter is a global SIP parameter that applies to all gateways. However, you can achieve per-gateway differentiation through the per-gateway Privacy settings and Enable local domain name settings, which modify how the From header appears independently of the global display from mode. For example, you can set SS_SIP_E164_DISPLAY_FROM to E164 display globally, then use per-gateway Privacy = Id for specific gateways where caller ID blocking is required. For advanced configuration assistance, contact us on WhatsApp at +8801911119966. 📱

❓ How do I troubleshoot caller ID issues related to VOS3000 SIP display from?

🔍 Start by examining the SIP INVITE messages in VOS3000’s SIP debug trace. Check the From header format, display name, Privacy header, P-Asserted-Identity header, and the domain portion of the From URI. Compare the actual signaling with your expected format. Common issues include: SS_SIP_E164_DISPLAY_FROM set to Ignore when the carrier requires E164, Mapping Gateway Caller set to the wrong field, Privacy = Id overriding display from settings, and private IP in the From URI domain. For comprehensive troubleshooting techniques, see our VOS3000 troubleshooting guide. 🔧

📚 Related Resources

🔗 Explore these related guides for comprehensive VOS3000 configuration knowledge:

• 📞 VOS3000 SIP Authentication — Complete 401/407 authentication configuration guide
• 📡 VOS3000 SIP Call Flow — SIP signaling flow and message sequence
• 🔧 VOS3000 SIP Session — Session timer and call management
• 📋 VOS3000 Parameter Description — Complete SIP parameter reference
• 📊 VOS3000 System Parameters — System-level parameter documentation
• 📞 VOS3000 Caller ID Management — Comprehensive caller ID configuration
• 🔒 VOS3000 P-Asserted-Identity Caller ID — PAI header configuration and privacy
• 🌐 VOS3000 Call Routing — Routing configuration and best practices
• 🖥️ VOS3000 Gateway Configuration and Routing Mapping — Gateway and mapping setup guide
• 🔍 VOS3000 Troubleshooting Guide — Debug and resolve common issues
• 📦 VOS3000 Installation — Server setup and deployment guide
• 💰 VOS3000 Billing System — Rating, CDR, and billing configuration
• 🌐 VOS3000 Official Downloads — Official software and documentation (external)

---

📞 Need Professional VOS3000 Setup Support?

For professional VOS3000 installations and deployment, VOS3000 Server Rental Solution:

📱 WhatsApp: +8801911119966
🌐 Website: www.vos3000.com
🌐 Blog: multahost.com/blog
📥 Downloads: VOS3000 Downloads

---